Protect Your Bumpers
With Solid Steel

Watch them
in action ▶
Proudly Made in America of Solid Steel
Sleek, Solid Steel, Unibody Design
Quick and easy one-time installation
Protect both front AND rear bumpers
Protects your bumpers 24/7
Good neighbor policy

Proudly Made in America of Solid Steel

4Bumpers was born and designed in New York. It is US patented, US trademarked and US fabricated. We are proud to say 4Bumpers is the only solid steel license plate frame parking bumper guard made in the US.

Sleek, Solid Steel, Unibody Design

We believe other parking bumper guards on the market are unsightly and weak. 4Bumpers is a uniquely designed and highly fabricated single piece of solid steel that protects your bumpers at the moment it counts, and its sleek and low profile design means passersby might not even notice it's there.

Quick and easy one-time installation

Most bumper guards require constant handling of their devices — flipping them out of the trunk when preparing to park and then flipping them back into the trunk when preparing to drive. 4Bumpers is different because it attaches through your existing license plate screw holes. It's a simple, one-time installation that you can set and forget.

Protect both front AND rear bumpers

Most bumper guards can't safely protect your front bumper because of risks in using their attachment straps under the hood. 4Bumpers solid steel unibody design uses no straps and can provide both front and rear parking bumper protection. Additionally, other front and rear bumper protectors can block the license plate which may result in costly tickets. 4Bumpers does not obstruct your license plate information.

Protects your bumpers 24/7

Hassle free. Maintenance free. Protects your bumpers 24/7. Once installed you're all set. Any parking bumper guard that requires your constant attention means one more item on your to-do list. 4Bumpers frees you up with 24/7 parking protection.

Good neighbor policy

Replaceable rubber edges come on all our products and serve a dual purpose-your 4Bumpers finish remains protected and the rubber edge does not damage other car bumpers.

Prime

Superior solid steel front and rear parking bumper protection that attaches through your license plate screw holes.

MORE INFO

Duo

The same superior solid steel used in PRIME and PRIME+ models with an even lower profile design.

MORE INFO

Prime+

Superior solid steel front and rear parking bumper protection that attaches through your license plate screw holes.

MORE INFO

Proudly made in the USA

×
×

Installation

4Bumpers products have a quick and easy one-time installation.

Use of a flat license plate mounting bracket is recommended when installing 4Bumpers. 4Bumpers will perform only as well as it is securely attached to your bumper-so please make sure your 4Bumpers and mounting bracket, if you have one, are all firmly secured and attached to your bumper.

DUO

4Bumpers Duo installs on your bumper in one position.

1

UNSCREW YOUR LICENSE PLATE AND DISCARD ANY EXISTING LICENSE PLATE FRAME.

2

POSITION 4BUMPERS DUO IN FRONT OF THE LICENSE PLATE AND YOUR LICENSE PLATE BRACKET.

3

ALIGN THE SCREW HOLES AND THEN SCREW 4BUMPERS DUO AND LICENSE PLATE SECURELY INTO YOUR LICENSE PLATE BRACKET.

PRIME

4Bumpers Prime may be rotated and installed in either of two positions, depending upon the height of your vehicle and license plate attachment area in the bumper (see below).

FRONT BUMPERS

On front bumpers with license plate attachment areas relatively low to the ground, we suggest you install 4Bumpers Prime with the rounded guard in the "upper" position.

For SUVs, Minivans and other cars with license plate attachment areas in higher positions, we suggest you install 4Bumpers Prime with the rounded guard in the "lower" position.

REAR BUMPERS

There is greater variation in the height of license plate attachment areas on rear bumpers.

If your license plate attachment area is relatively low to the ground, we recommend you install 4Bumpers Prime with the rounded guard in the "upper" position.

In other instances we suggest you install 4Bumpers Prime with the guard in the "lower" position.

×
×